PSC Series

Air Cooled Smart Chiller with Scroll Compressor

  • The PSC series meets or exceeds the new ASHRAE 90.1 efficiency levels at both full and part load efficiency.
  • The PSC chillers offer low sound power levels, measured in accordance with the BS ISO 3744 standard. The low sound power levels make the APSa ideal for sound sensitive applications such as schools, hospitals, and sites located in residential neighborhoods.
  • The PSC chillers feature compact footprints and are suitable for close-spacing installation to serve the areas that have space constraints.
  • To ensure the best performance, all the chillers in the PSC series are factory-run tested, produced in an ISO 9001-2015 listed manufacturing facility & certified according to AHRI standard 550/590.
  • laboris nisi ut aliquip ex ea commInstallation is made quick and easy with complete factory wiring, easy lifting provisions, factory installed options and start-up. To eliminate potential start-up problems, a complete factory- test run is performed on each unit.
  • Petra introduces the PSC chillers as a single piece unit with single power entry. This unique single unit design provides the largest capacity in one chiller model with a compact footprint.
Download Brochure
  • SWelded structural C-channel base painted with mono component catalyzed primer sprayed paint.
  • Base is equipped with welded brackets for heavy duty lifting lugs.
  • Structural members are made from gauge 15 [1.8 mm (0.07 inch)] tubular cross members that are semi welded with stainless steel fasteners. All members & panels (side & roof) are painted with oven baked polyester electrostatic powder paint.
  • High performance hermetic scroll compressor.
  • Condenser coils are microchannel type (MCHE) or copper tubes copper aluminum type.
  • All coils are air pressure tested by dry air up to 2,900 kPa (420 Psi) under water. They also undergo dry cleaning after manufacturing for optimum system cleanness.
  • Condenser coils are covered with protective panels, to ensure uniform air distribution across the coil face area & provide additional protection for coil from weather elements.
  • Condenser fans of the external rotor type with many attractive features such as space saving, compact design, optimum cooling, full speed controllability and low starting currents.
  • High efficiency direct expansion (DX) shell and tube type coolers with inner grooved tubes to optimize the cooler’s efficiency.
  • Coolers are tested and stamped for refrigerant side design pressure of 1,000 kPa (145 Psi) and for a maximum water side working pressure of 1,500 kPa (220 Psi).
  • Liquid, discharge and suction pipes are all hard copper pipes. They are formed using automated CNC pipe bending machines in order to minimize pipe-brazed joints which in turn increases system reliability.
  • Epoxy paint for all exposed copper piping system of the refrigeration circuit.
  • Components of each refrigeration circuit include liquid line solenoid valve, liquid line shut off valve, liquid line moisture indicator sight glass, high safety pressure switch and replaceable core type filter.
  • Unit is fully charged unit with R410a/R407c refrigerant.
  • Compressor electronic current monitor and overload protection through controller
  • Copper tubes copper fins coil.
  • Coil corrosion protection including polyurethane pre-coating (for aluminum fins) and polyurethane post-coating (for aluminum & copper fins).
  • Sound reduction options including low rpm condenser fan and compressor jacket.
  • coil guard placed on the lower part of the unit all over the perimeter to provide protection for unit components, fabricated from gauge 18 [1.25 mm (0.05 inch)] galvanized steel sheet metal & painted with Petra electrostatic powder paint, fitted in place by spring load quick turn latch and is supported upon opening by stainless steel hinges.
  • Hot gas bypass consists of a mechanical valve capacity regulator used to adapt compressor capacity to actual evaporator load, installed in a bypass line between the high and low pressure sides of the refrigeration system and is designed for hot gas injection into the evaporator just after the expansion valve.
  • Pressure gauges for monitoring of refrigeration discharge and suction pressure.
  • Pressure relief valve set to open at a predetermined set pressure to protect pressure vessels and other equipment from being subjected to pressures that exceed their design limits.
  • Water flow switch installed to prevent operation of unit without evaporator water flow.
  • Cooler cladding of aluminum, stainless steel or painted galvanized steel {made from gauge 22 [0.7 mm (0.03 inch)}.
  • Cooler can be insulated with closed cell foam insulation of 25 mm (1 inch), 38 mm (1.5 inch) & 50 mm (2 inch) The insulation density is 48 kg/m3 (3 lb/ft3) with a K-factor of 0.035 W/(m.°K) [0.0203 BTUH/(ft.°F).
  • Main disconnect switch used to de-energize the power supply to the chiller during servicing or repairing works because of the door interlock with an external handle that is installed on the electric panel door
  • Power factor correction used to improve the power factor level which improves system reliability, minimizes voltage drops and gives better power quality.
  • Earth leakage relay used in electrical installations with high earth impedance to prevent shock
  • Control transformer to supply power input to auxiliary components at 120 or 220 volts, such as (not limited to) bulk head light and GFI outlet.
  • IP 54 protection, class I electric safety bulk head light.
  • Ampere-meter & volt-meter used to measure the power current & voltage consumption Ampere-meter is used for each phase.
  • 120 volt power supply connected through the transformer to provide a 120 volt single phase circuit that is used to operate the electric appliances at site such as laptops, tablets and cell phones.
  • Speed regulator for condenser fan motors used to permit the unit to operate in low ambient temperature

Residential ​Air Cooled Water Chillers

PETRA RWC Chillers are designed to meet customer requirements by offering state of the art low sound, reliability, high energy efficiency and small physical footprint chillers. The wide range of cooling capacities and flexible installation arrangement makes it easy to install and maintain.PETRA RWC Chillers are designed to be shipped as a complete factory package which are 100% run tested in the factory.PETRA RWC4 Chillers are equipped with an intelligent microprocessor controller to manage the unit performance for optimum efficiency at both full load and part load values.

RWC4 / RWCc

Air Cooled Residential Chiller with Scroll Compressor

  • Welded structural base painted with mono component catalyzed primer sprayed paint.
  • Base is equipped with welded brackets for heavy duty lifting lugs.
  • High performance hermetic scroll compressor.
  • Condenser coils are copper tubes copper aluminum type.
  • All coils are air pressure tested by dry air up to 2,900 kPa (420 Psi) under water. They also undergo dry cleaning after manufacturing for optimum system cleanness.
  • Condenser fans of the external rotor type with many attractive features such as space saving, compact design, optimum cooling, full speed controllability and low starting currents.
  • Brazed plate heat exchanger consists of stainless steel plates permanently brazed with pure copper filter (for small models) .
  • High efficiency direct expansion (DX) shell and tube type coolers with inner grooved tubes to optimize the cooler’s efficiency (for large models).
Download Brochure
  • Coolers are tested and stamped for refrigerant side design pressure of 1,000 kPa (145 Psi) and for a maximum water side working pressure of 1,500 kPa (220 Psi).
  • Liquid, discharge and suction pipes are all hard copper pipes. They are formed using automated CNC pipe bending machines in order to minimize pipe-brazed joints which in turn increases system reliability.
  • Epoxy paint for all exposed copper piping system of the refrigeration circuit.
  • Components of each refrigeration circuit include liquid line solenoid valve, liquid line shut off valve, high safety pressure switch and disposable core type filter.
  • Components of each refrigeration circuit include liquid line solenoid valve, liquid line shut off valve, high safety pressure switch and disposable core type filter.
  • Thermostatic expansion valve.
  • Free terminal for remote ON/OFF connection.
  • Free terminal for general alarm output.
  • Control voltage is 220-240V for all components.
  • Single point power connection for each electrical panel.
  • Starting contactors for compressors and condenser fan motors.
  • ON/OFF switch for each compressor.
  • Control circuit breaker for short circuit protection.
  • Short cycling protection for compressors (time delay).
  • Control transformer mounted & wired that shall supply all unit control voltage from main unit power supply to internal components such as (not limited to) solenoid valves, compressor motor protector, compressor crank case heater and microprocessor controller.
  • Microprocessor controller for full management of chiller operation and safety circuits.
  • Power supply monitor (phase failure relay) used to protect the power circuit against over or under voltage conditions and against phase loss or loss reversing conditions.
  • Nema 3X with IP54 minimum enclosure standard electrical panel. Two separate panels, one for power & the other for control.
  • Cooler tape heater protection down to 0°C (32°F), -18°C (0°F) & -29°C (-20°F).
  • Nema 4x electrical panels made from stainless steel.
  • Nema 4x electrical panels made from galvanized steel.
  • Circuit breaker for each condenser fan motor.
  • Circuit breaker for each compressor.
  • External over load for each condenser fan motor.
  • External over load for each compressor.
  • Dual power connection, one power entry for compressors & the second for the rest of the unit.
  • Speed regulator for condenser fan motors used to permit the unit to operate in low ambient temperature.
  • 120 volt power supply connected through the transformer to provide a 120 volt single phase circuit that is used to operate the electric appliances at site such as laptops, tablets and cell phones.
  • Ampere-meter & volt-meter used to measure the power current & voltage consumption Ampere-meter is used for each phase.
  • Control transformer to supply power input to auxiliary components at 120 or 220 volts, such as (not limited to) bulk head light and GFI outlet.
  • Earth leakage relay used in electrical installations with high earth impedance to prevent shock
  • Power factor correction used to improve the power factor level which improves system reliability, minimizes voltage drops and gives better power quality.

Water Cooled Water Chillers

Petra’s water cooled liquid chillers (WPSa) with a wide range of capacities and exceptionally high efficiencies, were designed to meet customer requirements for a variety of applications.Petra WPSa chillers offer state of the art low sound, high quality and reliability, optimized performance and a compact physical footprint.Petra WPSa chillers with semi-hermetic screw compressors and R-134a HFC refrigerant are 100% factory tested and commissioned to ensure efficient performance at specified operating conditions.

WPSA

Water Cooled Water Chiller with Screw Compressor

  • The WPSa series meets or exceeds the new ASHRAE 90.1 efficiency levels at both full and part load efficiency.
  • The WPSa series is available as a door way or extended chassis design
  • The WPSa chillers feature compact footprints and are suitable for close-spacing installation to serve the areas that have space constraints.
  • To ensure the best performance, all the chillers in the WPSa series are factory-run tested, produced in an ISO 9001-2015 listed manufacturing facility & certified according to AHRI standard 550/590.
  • Installation is made quick and easy with complete factory wiring, easy lifting provisions, factory installed options and start-up. To eliminate potential start-up problems, a complete factory- test run is performed on each unit.
  • Suction lines are insulated with closed cell foam insulation, then wrapped with a special protective material and finally epoxy coated. This gives further protection for the insulation against weather and other factors.
  • Other exposed copper pipes and headers are epoxy coated after being cleaned, to maintain pipe material and brazing protected against external conditions.
  • Petra paint is certified according to ASTM 117 A&B 5000 hours salt spray test.
Download brochure
  • Petra paint is certified according to ASTM 117 A&B 5000 hours salt spray test.
  • Base is equipped with welded brackets for heavy duty lifting lugs.
  • Structural members are made from gauge 15 [1.8 mm (0.07 inch)] tubular cross members that are semi welded with stainless steel fasteners. All members & panels (side & roof) are painted with oven baked polyester electrostatic powder paint.
  • Suction gas-cooled semi-hermetic twin screw compressor with variable slide valves allow the chillers to match actual load conditions, delivering exceptional part load performance.
  • High efficiency direct expansion (DX) shell and tube type coolers and condensers with inner grooved tubes to optimize the cooler’s efficiency.
  • Coolers and condensers are tested and stamped for refrigerant side design pressure of 1,000 kPa (145 Psi) and for a maximum water side working pressure of 1,500 kPa (220 Psi).
  • Independent refrigeration circuit per compressor.
  • Liquid, discharge and suction pipes are all hard copper pipes. They are formed using automated CNC pipe bending machines in order to minimize pipe-brazed joints which in turn increases system reliability.
  • Epoxy paint for all exposed copper piping system of the refrigeration circuit.
  • Components of each refrigeration circuit include liquid line solenoid valve, liquid line shut off valve, liquid line moisture indicator sight glass, high safety pressure switch and replaceable core type filter
  • Unit is fully charged unit with R-134a refrigerant.
  • Electronic expansion valve: Electronically Operated Step Motor flow control valves, intended for the precise control of liquid refrigerant flow. Synchronized signals to the motor provide discrete angular movement, which translates into precise linear positioning of the valve piston. Easily interfaced with microprocessor based controllers.
  • Compressor electronic current monitor and overload protection through controller.
  • Free terminal for remote ON/OFF connection.
  • Free terminal for general alarm output.
  • Control voltage is 220-240V for all components.
  • Single point power connection for each electrical panel.
  • Circuit breaker for each compressor.
  • – ON/OFF switch for each compressor.
  • Control circuit breaker for short circuit protection.
  • Short cycling protection for compressors (time delay).
  • Control transformer mounted & wired that shall supply all unit control voltage from main unit power supply to internal components such as (not limited to) solenoid valves, compressor motor protector, compressor crank case heater and microprocessor controller.
  • Microprocessor controller for full management of chiller operation and safety circuits.
  • Power supply monitor (phase failure relay) used to protect the power circuit against over or under voltage conditions and against phase loss or loss reversing conditions.
  • Nema 3X with IP54 minimum enclosure standard electrical panel. Two separate panels, one for power & the other for control.
  • Hot gas bypass consists of a mechanical valve capacity regulator used to adapt compressor capacity to actual evaporator load, installed in a bypass line between the high and low pressure sides of the refrigeration system and is designed for hot gas injection into the evaporator just after the expansion valve.
  • Pressure gauges for monitoring of refrigeration discharge and suction pressure.
  • Pressure relief valve set to open at a predetermined set pressure to protect pressure vessels and other equipment from being subjected to pressures that exceed their design limits.
  • Water flow switch installed to prevent operation of unit without evaporator water flow
  • Cooler cladding of aluminum, stainless steel or painted galvanized steel {made from gauge 22 [0.7 mm (0.03 inch)}.
  • Cooler can be insulated with closed cell foam insulation of 25 mm (1 inch), 38 mm (1.5 inch) & 50 mm (2 inch) The insulation density is 48 kg/m3 (3 lb/ft3) with a K-factor of 0.035 W/(m.°K) [0.0203 BTUH/(ft.°F).
  • Main disconnect switch used to de-energize the power supply to the chiller during servicing or repairing works because of the door interlock with an external handle that is installed on the electric panel door.
  • Power factor correction used to improve the power factor level which improves system reliability, minimizes voltage drops and gives better power quality.
  • Control transformer to supply power input to auxiliary components at 120 or 220 volts, such as (not limited to) bulk head light and GFI outlet.
  • IP 54 protection, class I electric safety bulk head light.
  • Ampere-meter & volt-meter used to measure the power current & voltage consumption Ampere-meter is used for each phase.
  • 120 volt power supply connected through the transformer to provide a 120 volt single phase circuit that is used to operate the electric appliances at site such as laptops, tablets and cell phones.
  • External over load for each compressor.
  • Nema 4x electrical panels made from galvanized steel.
  • Nema 4x electrical panels made from stainless steel.
  • Cooler tape heater protection down to 0°C (32°F), -18°C (0°F) & -29°C (-20°F).

Air Handling Units

PETRA Air Handling units (PAH) are designed with high quality and efficiency to meet the most demanding requirements. They provide cooling, heating and ventilation to conditioned space. These units are suitable for hotels, hospitals, large halls, banks, supermarkets and other applications.The flexible modular design allows various section arrangements according to the task requirement. This range covers air flow rates from 600 L/s (1,200 CFM) to 21,000 L/s (45,000 CFM) in a single piece unit. Custom designs are available up to 94,000 L/s (200,000 CFM) Units can be constructed as single piece, stacked, side by side or modular, and can fit as a door way.

Comfort Maker

  • Compact unit size.
  • Suitable for concealed ducted installation.
  • Available with a wide range of capacities from 736 L/s (1,560 cfm) to 4,719 L/s (10,000 cfm).
  • Unit models CM15, CM20, CM 24, CM30 and CM38 can be suspended from the ceiling and other models are provided with legs for floor or ceiling mounting.
Download Brochure
  • All units are constructed of heavy gauge galvanized steel. The side panels are removable for the inspection, adjustment and servicing of the coil and motor fan assembly.
  • All units are internally lined with 25 mm (1.0 inch) fiberglass insulation or its equivalent.
  • Double inlet, double width centrifugal forward curved fans are used, with V-belt drive with variable pitch pulley.
  • All CM models are provided with 25 mm (1.0 inch) nominal thickness aluminum mesh media flat filter
  • Coils are manufactured from seamless copper tubes mechanically-expanded into aluminum fins to be suitable for working at 3,068 kPa (300 Psi) air pressure. All coils are air pressure tested at 3,100 kPa (450 Psi), under water to avoid leakage.
  • All units are provided with a heavy gauge zinc coated galvanized steel drain pan.
  • Double skin (solid or perforated).
  • Stainless steel drain pan.
  • Stainless steel casing.
  • Backward curved fans.
  • External motor overload protection.
  • Main power circuit breaker.
  • Electric heater built inside the unit for heating purposes.
  • Manual/digital room thermostat.
  • 50 mm (2.0 inch) or 100 mm (4.0 inch) nominal thickness flat filter.
  • Synthetic fiber media for flat filter.
  • Copper tubes Copper fins coil.
  • Corrosion protection including polyurethane pre-coating and polyurethane post-coating.

PAH

Central Station Air Handling Unit

 PETRA Air Handling units (PAH) are designed with high quality and efficiency to meet the most demanding requirements. They provide cooling, heating and ventilation to conditioned space. These units are suitable for hotels, hospitals, large halls, banks, supermarkets and other applications.The flexible modular design allows various section arrangements according to the task requirement. This range covers air flow rates from 600 L/s (1,200 CFM) to 21,000 L/s (45,000 CFM) in a single piece unit. Custom designs are available up to 94,000 L/s (200,000 CFM) Units can be constructed as single piece, stacked, side by side or modular, and can fit as a door way.Petra’s PAH units are EUROVENT performance certified, and built from modular sections, allowing units to be fitted and sized exactly to customers’ specifications.A computer selection program allows fast and accurate selection of PAH units at different conditions. These units are widely used in a variety of applications.The units are designed to provide easy service and access to major components. Quick release access doors/panels offer complete accessibility to fans, coils and filters

DOWNLOAD BROCHURE
  • Double Wall G-90 galvanized steel with 50mm (2”) injected foam, 3 pcf insulation density as minimum.
  • Thermally broken panels/doors along the full parameter.
  • Standard panels/doors are galvanized steel with a machine applied foam gasket that seals all around its edges.
  • Flat roof cover with standing top seams extended to make rain gutters along the unit perimeter to ensure positive rainwater drainage.
  • Dampers are made with rigid aluminum frame with multi airfoil aluminum blades so as to reduce pressure drop and sound generated when air passes through the blades.
  • Flat Filter can be Pleated (MERV 1 – 4), Synthetic (MERV 5) or Aluminum (MERV 7 – 8).
  • Coils are manufactured from seamless copper tubes mechanically expanded into aluminum fins, with type-L, heavy wall, and seamless copper tubes for the coil headers.
  • Coils are designed to deliver their respective duties at optimum performance under all design conditions, tested at 3,100 kPa (450 Psi) air pressure under water.
  • Drain pan is made of 1.5mm (0.06 Inch) thick painted galvanized steel.
  • Double Width Double Inlet (DWDI) Centrifugal fan (forward, backward or air foiled curved).
  • Stainless steel and aluminum panels/doors
  • Inspection window (rectangular/circular)
  • Double sloped roof canopy with standing top seams and rain Gutters along the full canopy perimeter to ensure positive rainwater drainage
  • Face and by-pass damper
  • Mixing box module
  • Damper could be linked for motorized operation
  • Economizer section
  • Vee Filter (available for pleated, synthetic & aluminum flat filter types)
  • Bag Filter / hepa Filter
  • Copper tubes Copper fins coil
  • Corrosion protection including polyurethane pre-coating and polyurethane post-coating
  • Stainless steel drain pan
  • Single Width Single Inlet (SWSI) plenum fans
  • Single Width Single Inlet (SWSI) EC fans
  • Fan/motor drive assembly belt guard
  • Heat Recovery including energy wheel, heat pipe & cross flow heat exchanger
  • Gas Heater
  • Steam Humidifier
  • Additional sections including sound attenuator, diffuser, sand trap louver, droplet eliminator …etc.
  • Electrical options including electric heater, bulk head light, ultraviolet light, variable frequency drive (VFD) …etc.

Date Center Equipment

Petra understands the importance of environmental control for sensitive equipment and offers its Computer Room Split Air Conditioner.PASC Series is specifically designed to be used wherever temperature, humidity and filtered air have to be controlled continuously within close tolerance limits.Sensitive Electronic devices require demanding & controllable environment throughout the year (24/7). Such devices have to be controlled in terms of humidity and internal temperature to close tolerance limits.Typical requirements of such environment is to maintain internal conditions  between 16-28 °C (60.8-82.4 °F) with moisture content of 50-60% relative humidity.Computers & communications systems generate 6-10 times the heat load of normal occupied spaces and they require state of art air conditioning equipment to control them They can be installed in data centers, tele-communications centers, laboratories, computer server data rooms, network operation centers, testing facilities and others.

PASC

Air Conditioner Split Computer Room Units

  • Petra PASC units has been developed and based on proven design and in house testing according to the highest international standards. It is used in various of systems all over the world
  • Petra PASC units provides the highest energy efficiency both at operating & running conditions and thus provides the lowest operating cost. This is achieved by using the most reliable and energy efficient electronic components.
  • Savings are obtained by using optional digital scroll compressor, EC fan motors, external rotor condenser fans and Petra piece of art microprocessor controller
  • Unmatched corrosion resistance with oven baked powder coat (5,000 hours salt spray test) the highest in industry
  • Unmatched corrosion resistance with oven baked powder coat (5,000 hours salt spray test) the highest in industry
  • Microprocessor controller built to space requirements with intelligent alarm and diagnostic system that can prevent a problem before it occurs. Full refrigerant system control with air delivery variation to deliver the specific space load requirements with the lowest energy consumption ever
  • Down flow and up flow configurations are available to suit a wide range of room applications. Different choice of compressors from on/off or digital to match space performance with optimal efficiency
  • Front access panel for service and maintenance that saves floor space. Front access using hinged doors.
  • Petra PASC to be mounted against a wall or partitions on adjacent to or back at other equipment. All unit components are accessible from the front panels for maintenance or replacement Built-in humidity and reheat devices. Ozone friendly refrigerants (R-407c & R-410a). Full microprocessor control panel with different BMS connectivity’s and full diagnostic system
DOWNLOAD BROCHURE

PASC CM

Mini Computer Room Units – Ceiling / Wall / Floor Mounted

  • PASC CM units feature slim & compact footprints and are suitable for minimal service requirement spacing installation
  • Unmatched corrosion resistance with oven baked polyester electrostatic powder coat certified up to 5,000 hours salt spray test as per ASTM 117 A&B
  • Microprocessor controller built to space requirements with intelligent alarm and diagnostic system that can prevent a problem before it occurs
DOWNLOAD BROCHURE
  • Full refrigerant system control with air delivery variation to deliver the specific space load requirements with the lowest energy consumption ever.
  • Wall mounted and floor mounted configurations are available to suit a wide range of rooms applications
  • Front access panel for service and maintenance that saves floor space. Front access allows Petra PASC CM to be mounted against a wall or partitions on adjacent to or back at other equipment
  • Built-in humidity and reheat devices
  • Ozone friendly refrigerants (R-407c & R-410a)
  • Full microprocessor control panel with different BMS connectivities and full diagnostic system
  • Pleated & Synthetic media filters are available
  • Copper tubes aluminum fins & copper tubes copper fins coil
  • Coil corrosion protection including polyurethane pre-coating (for aluminum fins) and polyurethane post-coating (for aluminum & copper fins)

Exhaust Fan

Petra exhaust fan series includes the Smart and Full Duty models. These units are used to remove exhaust air from areas such as restrooms, kitchens, restaurants hospitals and factories

PEXT

Petra Exhaust Fan Unit

  • Capacities from 50 L/s (100 CFM) to 4700 L/s (10,000 CFM).
  • Full Duty Models.
  • Factory Pre-Wired.
  • The fan units are designed to meet the requirements of different applications varying from residential projects to large factories, due to the wide range of capacities provided.
DOWNLOAD BROCHURE
  • The fan units are designed to meet the requirements of different applications varying from residential projects to large factories, due to the wide range of capacities provided.
  • The units can be installed on the roof as free discharge units or internally as ducted discharge units depending on the application and the customer’s requirement.
  • Factory pre-wiring and testing of all electrical components such as motor, air flow switches, controllers and failure switches guarantees high performance levels and reduces the required work at the site.
  • Maintenance for the unit may be done by removing the top access cover that provides an area large enough for all types of maintenance. The electrical box is accessible from outside the casing.
  • For special cases where standard designs do not fulfill the customer’s requirements, custom-made designs can be made available.

Fan Coil Units (DC Series)

PETRA’s fan coil units (DC Series) are designed for applications with medium static pressure. The units are particularly suitable for concealed or exposed ceiling or floor applications with ducted air distribution.This series covers an airflow range from 283 to 1,416 L/s (600 to 3,000 CFM). The standard unit is comprised of a coil suitable for both chilled and hot water, a fan section with direct drive centrifugal fan and a flat filter. Low water flow rate units are available with 9.8⁰C (16⁰F) temperature difference between inlet & outlet water.

DC / RAC

Fan Coil Unit for Medium Static Pressure.

  • Low sound level units, NC as low as NC 30
  • Low height and footprint units
  • Coil can be on the left or right without affecting coil performance (Except PFC & PCC coil that can only be on the right)
  • Coil is supplied with 2-air vents piped to the drain pan
  • Heavy gauge sheet metal casing with G90 – galvanized steel
  • Flexibility in shaped flow resistance
DOWNLOAD BROCHURE
  • Coils are constructed of copper tubes, 9.5 mm (3/8 inch) in diameter, mechanically expanded into aluminum fins
  • All coils are tested for leakage at 3,100 kPa (450 Psi) air pressure and suitable for up to 2,410 kPa (350 Psi) working pressure (with manual air vent, piped to the drain pan)
  • Forward curved centrifugal fans of the double inlet type that designed for maximum efficiency and uniform air distribution
  • Fans are statically and dynamically balanced to ensure quiet operation and optimal performance
  • Fans are direct drive type with 3-speed and driven by permanent split capacitor electric motors (with internal thermal protection)
  • A 25 mm (1 inch) nominal thickness, 22.2 mm (7/8 inch) thick actual frame size with 15.8 mm (5/8 inch) thick aluminum media flat
  • Single sloped galvanized steel drain pan, insulated on its underside to prevent condensation
  • All units are constructed of heavy gauge galvanized steel without paint
  • All units are internally lined with 12.5 mm (0.5 inch) fiberglass insulation for the coil and fan section
  • Double skin with solid or perforated inner skin
  • Stainless steel drain pan
  • Auxiliary drain pan under 3-way valves
  • Synthetic media filter
  • Shut-off valve (loose item or built in the unit)
  • 4-pipe system units have a double coil (3-rows cooling + 1-row heating)
  • 3-way valve (loose item or built in the unit)
  • Built-in finned tube electric heaters with automatic thermal safety
  • Manual Room Thermostat includes a three-speed switch (wall mounted, loose item)
  • Digital Room Thermostat (wall mounted, loose item)
  • Three-Speed Switch (wall mounted, loose item)
  • Unit’s casing for none decorative units is coated with weatherproof, polyester powder electrostatic paint, oven-baked to ensure maximum gloss and hardness
  • Supply grills (for DCC and DCV models only)
  • Ducted return air unit with bottom withdrawal filter (for DCP models only)

1- Ceiling Basic Model with Plenum (DCP)

DCP models are designed for concealed ceiling installation above false ceiling with ducted supply air distribution and free return of air above the false ceiling. The plenum encloses the fan section of the basic unit. Units of this type consist of a coil, fan and flat filter

2- Ceiling Basic Model (DCB)

Units of this type consist of a coil and fan without a return plenum or filter

3- Ceiling Cabinet Model (DCC)

This is an enclosed version of the DCB model with a cabinet for ceiling installation either above the false ceiling or exposed. The cabinet is fabricated from heavy gauge galvanized steel with removable panels. This model is supplied with a return and supply duct connection and consists of a coil, fan and filter (side withdrawal type)

4- Vertical Cabinet Model (DCV)

This is an enclosed version of the DCB model with a cabinet for floor mounting with vertical air discharge and front return air. The cabinet is fabricated from heavy gauge galvanized steel with removable panels. This model is supplied with return and supply duct connections and consists of a coil, fan and flat filter (front withdrawal type)